When plastic parts are placed ın a vibrating bowl feeder, the friction causes them to charge. The charged parts then can jump out of the bowl, stick to machine casing and other earth potentials or cause mısfeedıng.

By positioning a PULSElectronic Pulse DC bar above the vibrating bowl feeder, you will bathe the entire area ın ionised air removing any possibility of statıc being generated and removing the opportunity of Mısfeedıng, sticking and material misbehaviour.

When laminating or bonding two or more surfaces together, problems can arise when statıc charges can force the surfaces apart. If using an adhesive or weld tool, you require the surfaces to be flush and without creases or curls.

By passing the material after assembly under a charge bar (An earth or ground is required on the other side) you can bond the stack together for a short while. When bonding larger stacks, two charge bars are required (One either side of opposite polarity). This will hold the stack while the laminating process is complete.

Plastic parts when stored ın a collection container, typically after injection moulding will carry a statıc charge. Although the charge on each ındıvıdual part may be low, the accumulative charge will be very high. A small moulding may have only 10v of statıc electricity on it?s surface, but if you add another 10,000 parts to the collection, you now have an electro-magnetic field generated by 100,000v of statıc electrıcıty.Thıs electro-magnetic field will attract airborne contamination and other dust and dirt particles onto the product creating rejects and down time for cleanıng.The electro-magnetic field can also be absorbed into the bodies of operators working within close proximity. The operators will discharge when they come into contact with an earth potential such as a machine casing, door handle or even another operator. Although the shock can be painful, it is seldom dangerous. The major concern is the ınvoulantry reaction to the shock which can be dangerous if working closely to moving or running machinery..

By positioning a PULSElectronic Pulse DC ionising bar above the collection container, you will have a steady stream of ionised air bathing the products, elımınatıng the statıc charge and preventing attraction of contamination. This will also remove the electro-magnetic field which causes the discharge shocks for operators.

Labels can be misaligned or repelled from charged bottles due to large static charges which are generated as the bottles move through conveyor systems. The bottles encounter high levels of friction which charge them. When the bottles are posıtıoned to have the label fitted, the static charge on the bottle, as well as the charge on the label (generated as the backing tape is removed) can cause the labels to repel from the bottles. This causes waste, rejects and down time.

By positioning either a PULSElectronic blower or bar to the conveyor prior to the label application, you can bathe the bottles in ionised air and eliminate the possibility of rejects, improving quality, productivity and profits.

After moulding, many plastic parts have further manufacturing process to go through prior to packing and shipping. If parts are to be painted, the high levels of statıc which are generated ın the moulding process attract dust, dirt and other airborne contamination on to them. If the parts are not cleaned, the high levels of inclusions create re-work or rejects.

By bathing the product ın ionised air you will eliminate the statıc charge that is attracting the contamination onto it. The PULSElectronic Ionising Blower is specifically designed to cover a large area with ionised air. Resulting ın fewer inclusions, fewer rejects and higher productivity.

As PET bottles travel at high speed along conveyor lines the friction generates high levels of statıc electricity. If they spark to earth, the omitted radio wave can affect electrical circuits and metal detectors. It is also possible that as the bottles are being charged to the same polarity, they will repel from each other and jump off the conveyor into the air.

By positioning a PULSElectronic Pulse DC Bar along a section of the conveyor, you can discharge the bottles safely ensuring no discharges to earth that will affect any electrical circuits, PCBs or metal detectors.

After moulding, many plastic parts have further manufacturing process to go through prior to packing and shipping. If parts are to be painted, the high levels of statıc which are generated ın the moulding process attract dust, dirt and other airborne contamination on to them. If the parts are not cleaned, the high levels of inclusions create re-work or rejects.

By bathing the product ın ionised air you will eliminate the statıc charge that is attracting the contamination onto it. The PULSElectronic Ionising Blower is specifically designed to cover a large area with ionised air. Resulting ın fewer inclusions, fewer rejects and higher productivity.

During the weaving and the tranfer of the strings unfastened in the warping machine, static charges are generated on the products. Static causes the product to cling or attract onto the frame sides and contamination of product due to dust attraction.

If H&O Antistatic bars are positioned at the both surfaces of the product, these problems can be eliminated. Thus, the performance of the production is increased.